検索
Close this search box.

RAPIX Software

Get me quickly to:

RAPIX Addressing

RAPIX Addressing is the simple, fast and mobile solution for DALI Short Addressing.

To use RAPIX Addressing you will need a uDID – USB to DALI Interface Device:

RAPIX DALI Addressing Tool

Release Notes

Version 12.8.0, added: 21 March 2024

Improvements

  • Select correct default DALI-2 short address when adding DALI-2 input unit to the database.
  • Show new unit firmware version on the configuration dialogue after unit firmware update.
  • Fixed the Add Unit dialogue issue where it would appear populated with DALI-1 device types instead of DALI-2 device types.
  • Fixed the issue where adding DALI-1 push button would create a device in DB with unnecessary dry contact in it.

RAPIX Addressing v12.7 (19 March 2024)

New Features

  • Allow setting Operating Mode on selected DALI-2 units.
  • Added “Ramp Up or Down (Advanced)” template.
  • Added template “Toggle with Exit Delay and Flag”.
  • Double click light bulb icon now toggles Short Address on the Addressing view.
  • Added Edit button to the Groups and Scenes views.
  • Added Identify, Switch ON, and Switch OFF popup menu items to the Addressing view.

Improvements

  • Input Unit Templates
    • End of description missing on the template configuration dialogue.
    • Show when internal templates are used on the RAPIX Input configuration dialogue.
    • Error in zone selection is visible on template Config dialogue even though zone is selected.
    • The deprecation process does not work for internal events.
  • Incorrect tooltip on RAPIX Input dialogue.
  • Improve grids panel vertical scroll on the Addressing view.
  • Show error if Check For Updates fails to get products catalogue from Ozuno server.
  • RAPIX Mobile can have Confirm and Unconfirm buttons enabled at the same time.
  • Improved RAPIX Mobile web page help details.
  • RA sometimes shows unnecessary “Update firmware” warning for RAPIX input.
  • Disable Rules are not working on DALI-2 RAPIX sensors.
  • Added DALI Logging of QUERY RESET STATE, QUERY CONTENT DTR2, SET EXTENDED FADE TIME, GO TO LAST ACTIVE LEVEL, CONTINUOUS UP, and CONTINUOUS DOWN.
  • Fixed exceptions
    • Exception when updating eHub.
    • InvalidAsynchronousStateException when scanning DALI line.

RAPIX Addressing v12.6 (16 February 2024)

Improvements

  • When opening a RAPIX unit in editor, check that sensor DALI-2 settings are correct and prompt user to auto-correct them.
  • Show if DALI-2 settings are wrong for use with motion sensor templates.
  • When adding a template, set DALI-2 sensor properties.
  • Fixed the issue with not being able to program Motion Sensor unit.
  • Fixed the issue with not being able to select the Movement DALI-2 event filter.
  • Fixed problem with part of log filter not being visible.
  • Made the Zone editor drop-down wider on the Template editor dialogue so that long zone names would be fully visible.
  • Updated “Dwell while adjacent areas are on” feature of the Motion Sensor (Advanced) template to work better with multi-line Zones.
  • Improved Common Area Keep-On template.
  • Improved Colour Cycle template.

RAPIX Addressing v12.4 (12 February 2024)

New Features

  • Added new templates:
    • Dial (Advanced) template
    • Bistable Dry Contact Zone and Flag template

Improvements

  • Fixed the screen draw glitch on the template editor dialogue the Summary panel.
  • Enable or disable indicator brightness controls on the RAPIX Input UI depending on whether the DALI-2 Application Controller is enabled.
  • Fixed the issue with SA and Input Unit address grids appearing with missing digits after resizing main form.
  • Increased the height of the info panel at the bottom of the DALI-2 unit configuration dialogue.
  • Updated some templates:
    • Timer (Advanced) template
    • Dial Dimmer with Button Toggle
    • Bistable Dry Contact Toggle (Advanced) templates
    • Exhaust Fan Timer template
    • Scene Timer template

RAPIX Addressing v12.3 (8 February 2024)

New Features

  • Added support for DALI-2 Generic Instance Type.

Improvements

  • Fixed the issue causing option <Multiple Values> to appear when editing DALI-2 instance properties on a RAPIX input unit.
  • Allowed selecting Application Controller Enabled state on the DB-only RAPIX input unit.
  • Fixed exception sometimes occurring when opening 3rd party DALI-2 live unit.
  • Fixed the issue where RAPIX input unit sometimes appears not in sync after reopening project.
  • Signed 2 unsigned templates.
  • Allowed double-click in the Input Units grid on the Addressing view to open unit configuration dialogue.

RAPIX Addressing v12.2 (5 February 2024)

New Features

  • DALI-2 additions:
    • Added support for the DALI device type 254 (no device types implemented).
    • Show 8-digit serial number instead of 4 digits.
  • DALI-2 input unit (“control device”)support:
    • Detect during DALI line scan and resolve address conflicts.
    • Allow naming and confirming.
    • Allow Identification.
    • Allow programming of DALI-2 properties (62386-103, 62386-301, 62386-302, 62386-303 and 62386-304).
    • Allow placement on floor plans.
    • Added DALI-2 short address grid.
    • Added support in RAPIX Mobile.
    • Added to Project Report (list non-RAPIX input units by GTIN).
  • New Templates:
    • LCD Disable template.
    • Off with Exit Delay (Long Press) template.
    • 2-button colour temperature control template.

Improvements

  • Use colour coding for RAPIX units.
  • Terminology change: Device -> Unit.
  • Fixed the issue with non-displayable character sometimes appearing in unit and button name field.
  • Updated USI datasheet.
  • Fixed the ArgumentNullException sometimes appearing when attempting to update eHub firmware.
  • Prevented Name and Value column ordering on the unit Configuration form.
  • Improved templates:
    • Sunset Dimmer template.
    • Toggle Dimmer with Exit Delay template.
    • Toggle Dimmer Advanced template.

RAPIX Addressing v11.9 (20 November 2023)

  • Improvements
    – Fixed issue with the Dwell Level not able to be set in the Advanced Motion Sensor template.
    – Updated templates to use default dwell levels of 127 (50%) instead of 128 (50.4%).
    – Highlight faulty RAPIX devices on the Addressing view.
    – Fixed issue with Flag Timer template.
    – New Motion Sensor Vacancy Mode template.

RAPIX Addressing v11.8 (22 August 2023)

  • Improvements
    – Templates
    – Added option Timer template for turning the Zone off by button press.
    – Replaced the single Timer template with a more basic version and an advanced one.
    – Fixed problem with the ‘Toggle Dimmer with Exit Delay’ template when turning zone back on during exit delay.
    – Updated eHub LCD disable templates.
    – Improved UI performance on the Addressing view.
    – Fixed the issue with copy-paste not working when editing device name and allowed editing next device’s name on Tab key press.
    – Improved how RAPIX Addressing resolves device type conflicts.
    – Improved handling of compound vs non-compound LED device type mismatch.
    – GO Mobile not working sometimes on Windows 11.
    – eHub touchscreen button name can appear in the channel name on touchscreen.
    – Datetime does not appear on eHub touchscreen fallback page when it is set to Default theme.
    – Can’t save eHub programming if device name has special characters.
    – Grey out checkbox of a device on Addressing view if it can’t be confirmed.
    – Show “Scanning Line” overlay on Addressing view instead of “No network information”.
    – DALI logger window not opening sometimes.

RAPIX Addressing v11.5 (24 May 2023)

  • New Features
    – Added support for DALI Device Type 5 (DC Voltage Converter).
    – Show DALI Device Type when adding new device.
    – Warn if a DALI line is controlled by broadcast but has virtual devices or switched maintained EM devices.
  • Improvements
    – Fixed the issue with the DALI Line buttons appearing disabled incorrectly.
    – Improved mobile phone handling of processing delays.
    – Excel export
    – Fixed export where there are duplicate names.
    – Fixed export of hidden configured switches.
    – Fixed export for interfaces, lines, groups, scenes, and devices with blank names.

RAPIX Addressing v11.4 (8 May 2023)

  • New Features
    – Added support for Ozuno Blind & Shutter Relay.
    – DALI Logger:
    DALI Logger now remembers the selected item when filters are changed.
    DALI Logger has new button to scroll to selected item.
    Made RAPIX Sensor log messages more readable when there is no sensor device in DB.
    – Option to show grid on floor plans.
  • Improvements
    – Fixed the issue with Template Mode not working with some scene templates.
    – Fixed template editor issue with header section disappearing when it should be visible.
    – Prevented tree view from flickering during DALI line scan.
    – Made UI better reflect the actual state of devices during and after scan.
    – Updated the Long Range LLS datasheet.
    – Mobile Phone usage improvements:
    Return to previous page after error message is displayed.
    Prevent error message from sometimes being shown incorrectly.
    Allow mobile phone user to get control back if phone’s IP Address changes.
    – Fixed some exceptions.

RAPIX Addressing v11.2 (21 March 2023)

  • Improvements
    – Fixed the issue with RA incorrectly showing “Invalid Zone Names” error message when saving project.
    – Fixed menu Help/FAQ opening RI page.
    – Fixed the drop-down colour selection lists on eHub GUI showing text instead of colour.

RAPIX Addressing v11.1 (17 March 2023)

  • Improvements
    – Fixed bug with readdressing device using go mobile not confirming the device.

RAPIX Addressing v11.0 (16 March 2023)

  • New Features
    – Updated RAPIX Addressing to be a 64-bit application.
  • Improvements
    – Clearing USI device on UI will put it in the ‘from factory’ state and thus allow button identification.
    – Updated motion sensor templates to allow motion to turn on zone during dwell in vacancy mode.
    – Updated motion sensor templates to allow occupancy/vacancy to be set by Operating Property.
    – Fixed template form colour selection combo.
    – Fixed the issue with 30M disable rules not working.
    – Fixed display of colour DALI scenes for compound devices.
    – Fixed an exception occurring when closing the DALI Logger window while scanning DALI line.
    – Fixed exception opening RAPIX API form.
    – Fixed problem with mobile phone usage showing Communication Error sometimes.
    – Fixed exception when using DALI Log form for walk test.
    – Fixed display of colour DALI scenes for compound devices.

RAPIX Addressing v10.11 (17 November 2022)

  • Installer changes to better handle uninstallation of older versions of RAPIX Addressing.

RAPIX Addressing v10.10 (26 October 2022)

  • Fixed the error that was appearing when programming Dry Contact on RAPIX Motion Sensor.

RAPIX Addressing v10.9 (24 October 2022)

  • Increased time-out on mobile phone before showing error message.
  • Fixed display of selected colour in colour control templates.

RAPIX Addressing v10.8 (14 October 2022)

  • Fixed the issue with Confirm All Devices sometimes not working and Confirm individual device sometimes showing unnecessary warning.

RAPIX Addressing v10.7 (11 October 2022)

  • New colour control templates.
  • Fixed exception that could occur when opening DALI Log.
  • Fixed the issue with USI live device GUI not opening if there are programmed disable rules.
  • Fixed problem with setting the eHub rotary resolution.
  • Updated Motion Sensor with Exit Delay template.
  • Show an error message if function test or duration test fails to start on the device configuration dialogue.
  • When using Go Mobile, show error if phone goes out of WiFi range.
  • Prevent double click on mobile web page on iPhone from zooming.

RAPIX Addressing v10.6 (23 August 2022)

  • Added support for new products:
    • RAPIX Push Buttons
    • RAPIX Diva Buttons
    • RAPIX Dials
  • Added Tools menu item to allow stopping EM Function and Duration tests on site.
  • Allowed copying and pasting of DALI device properties.
  • Show pop-up hint on addressing tab showing compound device details.
  • Added Zone Tracking template.
  • Added Zone Logic template.
  • Improved logged DALI message when there is no Forward Frame.
  • In DALI Log, show details when setting colour or fade time.
  • Fixed problem in Mobile phone control where you could not navigate away from an unpowered DALI Line.
  • Fixed eHub motion sensor channel appearing without motion sensor inputs.
  • Warn if user has set warmest CT above coolest CT.
  • Allow wider selection of colour temperatures from addressing tab.
  • Warn user if pasting blank device configuration to another device.
  • Fixed exception when swapping eHub channels.
  • Show missing custom template ID on the error dialogue when loading programming from a RAPIX device.
  • When confirming a compound device where there is a minor mismatch in type, retain as much configuration data as possible.
  • Improved options for correcting mis-matched eHub channel.
  • Prevented exception occurring in some rare cases when scanning DALI line in RAPIX Addressing.
  • Allow scrolling on mobile phone button and sensor identify pages.
  • Fixed display of compound device type.
  • eHub GUI will now offer to Configure New channel whenever there is a channel type mismatch between DB and live.
  • Rotary and sensor inputs on eHub GUI will appear as circles while push button inputs will appear as rectangles with rounded corners.

RAPIX Addressing v10.5 (29 June 2022)

  • New features for mobile phone use:
    • Allow user to select DALI Line.
    • Identification of RAPIX buttons.
    • Identification of RAPIX sensors.
  • New options for allocating short addresses
    • Don’t use Short Address 0.
    • Allocate SA starting from low SA, or starting from high SA.
  • Improvements
    • Improved reporting of compound device types.
    • Fixed problem with reporting results of Short Address allocation.
    • Fixed problem with sync check of compound devices.
    • Allowed selecting Dynamic Fast Fade Time for LED DALI devices.

RAPIX Addressing v10.4 (23 May 2022)

  • Support for DALI Devices that implement multiple device types (“Compound Devices”).
  • Copy and paste of all templates from one RAPIX Device to another (sensors and Universal Input) without having to open the editor.
  • New icon for showing device sync status.
  • Allow sync of just selected devices.
  • Added Bistable Dry Contact Toggle (Advanced) template.
  • Fixed Dimmer Timer template.
  • Fixed operation of mobile phone control of group 15.
  • Renamed various items for clarity.

RAPIX Addressing v10.2 (17 March 2022)

  • Fixed USB DID Driver installer sometimes not installing the driver on new Win10 and Win11 laptops.
  • Improved info links that navigate to Ozuno web site.

RAPIX Addressing v10.1 (1 February 2022)

  • Added new template Scene Sequence (bistable dry contact).
  • Updated USB DID Driver.

RAPIX Addressing v10.0 (12 January 2022)

  • Added new “Dial with Selectable Granularity” template.
  • Improved the Xi Flag Change Event template.
  • Improved the Xi Operating Property Change Event template.
  • Hide “dial” templates for dry contact inputs.
  • In template editor, added text next to expand/contract chevron to show its purpose.
  • Fixed problem with colour select form not allowing colour selection for some devices.

RAPIX Addressing v9.8 (22 November 2021)

  • Added a DALI Query log filter option to enable the background query messages to be hidden.
  • Fixed problem with setting DALI scene colour.
  • The DALI log window will be removed from the task bar when closed.
  • Updated the Technical Support tab on the About box.

RAPIX Addressing v9.7 (25 October 2021)

  • Added location information for every DALI device.
  • Updates for log form:
    • Added option for viewing Button Pressed events to the Log Form.
    • Added Walk Test mode to Log Form.
  • DALI-2 support:
    • handle 8 byte serial numbers
    • show PING command in log
  • Improved handling of DALI Devices that don’t reply to valid READ MEMORY LOCATION commands.
  • Fixed problem with bottom of log filter view hidden.

RAPIX Addressing v9.5 (3 September 2021)

  • Allow setting the group membership of multiple devices on the Group tab using SHIFT + Click.
  • New Templates
    • Toggle Dimmer with Exit Delay
    • Motion Sensor with Two Delays
  • In Short Address list, highlight missing
  • Closing the DALI log now leaves it paused in the background so that the logged data is not lost.
  • In template drop-down lists, show items in sorted order.
  • Improved the wording of some error messages.
  • Improved the description of some templates.
  • When resolving address conflicts, attempt to move devices back to their correct address.

RAPIX Addressing v9.4 (17 June 2021)

  • Added Help menu.
  • New templates:
    • Light Level Report.
    • Do Nothing.
  • When hovering mouse over DALI Line shown in red, show hint describing problem.
  • Fixed problem with slave sensor template.
  • When using mobile phone to move, confirm or unconfirm devices, show device confirmed status (i.e. black).
  • Prevent exception when re-addressing devices.
  • Prevent exception when converting from Colour Temperature to RGB.
  • Added pop-up hint for everywhere that the perceived brightness “eye” icon is used.
  • Improved error message when saving to eHub fails.
  • While updating eHub or Xi Device firmware, prevent the rest of the program from being used.
  • Changed the default scene fade time to 1 second.
  • Improvements to eHub and Xi Disable Rule forms:
    • Allow long names to be seen in drop-down lists.
    • Sort items in drop-down list.
    • Increased width of columns.
    • Show a hint for long descriptions.
    • Clarified error message when trying to use an unused scene in a disable rule.

RAPIX Addressing v9.2 (19 April 2021)

  • New scene sequence template.

RAPIX Addressing v9.1 (1 March 2021)

  • The “Disable Out-of-box Behaviour” feature for Xi Sensors and Universal Inputs.
  • Clearing all addresses now includes Xi Devices.

RAPIX Addressing v9.0 (2 February 2021)

  • Fixed exceptions.

RAPIX Addressing v8.12 (29 October 2020)

  • Added support for the Long Range Xi Sensor.
  • Disabled indicator for Scene Cycle/Sequence templates.
  • Split room join template into three for clarity. Removed unused timer from toggle dimmer template.
  • Fixed bug with setting colour scenes.

RAPIX Addressing v8.11 (29 October 2020)

  • Templates
    • Added more blind control templates.
  • RAPIX Mobile
    • Allow addressing Xi Devices.
    • Allow setting DALI groups.
    • Allow DALI line scan.
    • Show basic info about the DALI Line.
  • Fixed ConstraintException Value ‘-1’ occurring sometimes when adding new Xi Scene.

RAPIX Addressing v8.10 (9 September 2020)

  • Templates
    • Fixed Scene Cycle template.
    • Improved handling of templates for dials.
    • Added Scene Cycle 2 button template for colour control.
    • Updated Scene Cycle template to work with button click as an option.
    • Added new option to Scene Timer template.
  • On Scene Blast form, added all/none buttons for mask.
  • Fixed sorting of schedule events by time.

RAPIX Addressing v8.9 (17 August 2020)

  • Improved reliability of the eHub firmware update over Ethernet.
  • Don’t show warning about no NTP on the eHub 3.0 GUI if there is no live device.

RAPIX Addressing v8.8 (4 August 2020)

  • Template light level control – allow larger hysteresis and show actual range.
  • Fixed problem with TimeZone selection for non-English versions of Windows.
  • Increased the height of the header of some templates.

RAPIX Addressing v8.7 (1 July 2020)

  • Fixed DALI group membership change on the Groups view affecting device identification.
  • Fixed the ObjectDisposedException exception that could occur when saving Universal Input programming while shortening and opening its dry contacts.
  • Fixed exception that could occur on eHub GUI when updating Ethernet info on the Info view.
  • Changed the way that eHub scenes are stored to fix issue with scene indicators.
  • Added Blind-control templates.
  • Added sunset switch for scenes template.
  • Added mode selection to Motion Sensor with Exit Delay template.
  • Log DALI Type 4 Application Extended Commands.
  • Added support for DALI-2 devices.

RAPIX Addressing v8.6 (1 July 2020)

  • Fixed the eHub 3.0 Schedules disabling feature.
  • Improved when warning message about no NTP service appears on the eHub 3.0 Schedules view.

RAPIX Addressing v8.5 (25 June 2020)

  • Fixed Go Mobile help page scrolling and phone simulator.
  • Improved support for RGBWAF DALI Type 8 devices.
  • Improved logging of exceptions related to opening Device Catalogue.
  • Fixed the eHub programming not loading from live device if it was programmed with a Scene Cycle template.
  • Fixed the exception sometimes occurring when clicking Clear button on the Xi Sensor GUI.

RAPIX Addressing v8.4 (17 June 2020)

  • IP address on the eHub 3.0 Info tab is now a clickable URL.
  • Don’t show Schedule info on the Xi Sensor and Universal Input GUIs.
  • Improved Xi Change templates.
  • Stopped showing warning about no NTP on the eHub 3.0 GUI Schedules tab when device is configured to Accept NTP Broadcasts.

RAPIX Addressing v8.3 (9 June 2020)

  • Added support for eHub Schedules.
  • Added information on eHub editor to show details of Ethernet and NTP (for eHub firmware 3.0 or later).
  • Added buttons to unconfirm all devices and clear short address of all devices.
  • Raise an error when attempting to edit Xi device entry when its DB and live types do not match.
  • Added help buttons to various locations to show related App Note.
  • Prevented internal event templates from appearing in the list of available templates when programming Xi Sensor.
  • Prevented PC from going to sleep when updating eHub or Xi Device firmware.
  • Stopped showing the error message about device type conflict when moving device to a different address.
  • Replaced Common Area Control template with two new ones.
  • Fixed header height on templates. Fixed maximum pulse level in templates.
  • In scene templates, added hyperlink to colour control App Note.
  • Allowed adding eHub v3.0 and eHub v2.3 to database.
  • Fixed the eHub firmware import throwing exception when importing from a network drive starting with double slash.
  • Fixed an exception occurring sometimes when confirming short addresses or using RAPIX Mobile.
  • Removed the Add button from the eHub GUI Templates page.
  • Clarified some of the eHub error messages.

RAPIX Addressing v8.2 (23 March 2020)

  • Improved firmware update of Rapix Emergency DALI devices.
  • Fixed the “Could not open project” error appearing when attempting to open a project.
  • Improved description of scene templates.
  • Improved behaviour with templates containing multiple DALI Scenes such as Scene Cycle.
  • Improved Motion Sensor templates.
  • Added Scene Cycle DALI template.
  • Added link to help/support information to some templates.
  • Allowed selecting colour on the Scene Blast dialogue.
  • Added Scene Auto-create to the Scene Blast dialogue.
  • Fixed the issue with getting device status from the offline devices.
  • Programming of Rapix input devices can now be force-saved, i.e. DB programming can be saved to live device even if nothing was changed on the device configuration dialogue.
  • Don’t allow using empty zones in Rapix input devices.
  • Added Common Area Control template.
  • Added main menu item Tools\View Logs.

RAPIX Addressing v8.1 (23 January 2020)

  • Show the correct number of inputs for the Universal Input device in database.
  • Allowed RAPIX Addressing download and automatically install RAPIX Input firmware images.
  • Updated Rapix TeamViewer Client to the latest version.

RAPIX Addressing v8.0 (31 December 2019)

  • Excel export of eHub Disable Rules.
  • Fixed the DALI logger issue where it would stop logging all traffic on a DALI line after receiving an unknown/malformed forward frame.
  • New installer:
    • Install software in \Program Files (x86)\Ozuno instead of \Program Files (x86)\Diginet
    • Store project files in \Documents\Ozuno instead of \Documents\Diginet
    • Store templates and firmware in \ProgramData\Ozuno instead of \ProgramData\Diginet
    • Changed registry settings from HKEY_CURRENT_USER\Software\Diginet to HKEY_CURRENT_USER\Software\Ozuno
  • Added templates:
    • Dim Only
    • Set Scene and Flag
    • Toggle (Long Press)
    • Bell Press (Long Press)
    • Dial/Button Dimmer
  • Improved template filtering to hide infrequently used templates.
  • Fixed device identification not working on the Xi device f/w update dialogue.
  • Fixed Dry Contact state sometimes appearing as Closed on UI even when that DC is actually open.
  • Added support for XY colour.
  • Fixed the Colour Value not saving to the Scene Colour table in the project database.
  • Fixed problem with colour devices not having auto activation enabled.
  • Added support for the Rapix Xi Universal Switch Input.

RAPIX Addressing v7.3 (16 October 2019)

  • Improved support for colour
    • Allowed setting colour for the selected devices, groups and broadcast. Also allowed the Set Colour dialogue height change dynamically when selecting colour type.
    • Added colour details to project report.
  • Dynamic tooltip and icon on the Addressing view for non-compliant devices, errors, sync and other issues.
  • Reworked identification of the eHub channels and added identification of eHub individual inputs.
  • Groups and scenes will now be automatically preselected in the identification drop-down list when selecting them on the Groups and Scenes views.
  • Added dial/dimmer template.
  • Disabled Xi device editing when device’s DB and network types are different.
  • Allowed resizing the Device Name column on the Addressing view. The column size will be set to default when software starts.
  • Fixed bug with saving MASK colour to live devices from DALI device editor.
  • In DALI Device editor, if GTIN or serial is invalid, show as “N/A”.
  • Fixed a problem with resetting DALI Type 8 devices.
  • Changed the Motion and Light Level Sensor template name to Motion in Darkness.
  • Fixed Motion Sensor With Exit Delay template.
  • Fixed the issue with Global DALI Device Programming not saving scene changes to live devices.
  • It will no longer be possible to accidentally delete confirmed devices when deleting multiple selected devices.
  • Allowed unconfirming Xi address if it happened to be occupied by a DALI interface device after address conflict resolution.
  • Improved the appearance of title on the Network, Zones and Xi Scenes views when resizing panels with a splitter.
  • Prevented the Network Interfaces tree from expanding when main window maximises.
  • Confirming Xi device will now change the database device type if it is not the same as on live device.
  • Fixed the Xi Sensor motion indicator green ring not appearing on GUI when motion is detected.
  • eHub GUI will no longer show a dry contact open or closed state if there is no live device.
  • Project Report now includes eHub internal events.
  • Fixed an exception occasionally occurring when changing device’s address.
  • Fixed the Disable Rules dialog not appearing for an Xi Sensor dry contact.
  • Updated the Tech Support tab on the About box.

RAPIX Addressing v7.2 (15 August 2019)

  • Improved Dry Contact usage by allowing dimmer and advanced templates.
  • Improved Toggle Advanced template.
  • Reduced log time stamp decimal places.
  • Fixed the NullRefernceException occurring when starting RAPIX Addressing on Windows 7 that has Firewall blocking Mobile web server port.
  • Improved Add Device dialogue
  • Improved filtering of allowed templates on a RAPIX DALI Xi Occupancy Sensor dry contact.
  • Added Motion Sensor and Exit Delay template.
  • Tidied templates that use internal events.
  • Added Ozuno web site link to the About box.
  • Added Xi Devices Global Programming.

RAPIX Addressing v7.1 (15 August 2019)

  • Improved Dry Contact usage by allowing dimmer and advanced templates.
  • Improved Toggle Advanced template.
  • Reduced log time stamp decimal places.
  • Fixed the NullRefernceException occurring when starting RAPIX Addressing on Windows 7 that has Firewall blocking Mobile web server port.
  • Improved Add Device dialogue
  • Improved filtering of allowed templates on a RAPIX DALI Xi Occupancy Sensor dry contact.
  • Added Motion Sensor and Exit Delay template.
  • Tidied templates that use internal events.
  • Added Ozuno web site link to the About box.
  • Added Xi Devices Global Programming.

RAPIX Addressing v7.0 (10 July 2019)

  • Added support for the RAPIX DALI Xi Occupancy Sensor.
  • Added project export to Excel.
  • Display the current light level sensor reading on the eHub GUI.
  • Added the Motion and Light Level Sensor template.
  • Fixed all exceptions reported by users.
  • Fixed the Confirm All button remaining disabled after unconfirming a device.
  • Software auto-update changed to use a new server.
  • Clarified what type of eHub input can be used with each template.
  • Improved local interface detection by the Fast Scan.

RAPIX Addressing v6.15 (5 April 2019)

  • Improved German translations.

RAPIX Addressing v6.14 (15 March 2019)

  • Fixed issues with editing multi-selected colour devices.

RAPIX Addressing v6.13 (13 March 2019)

  • Added support for DALI Type 8 (Colour Control) devices.
  • Changed DALI device default fade time/rate to “dynamic”.
  • Fixed Tool/Export Logs menu item.
  • Fixed selection of “live” grid in RAPIX Addressing.
  • Enable missing DALI Devices to be seen more easily.
  • Added FAST SCAN (i.e. scan for new devices).
  • Fixed the check for updates incorrectly detecting an Emergency device firmware, which has already been previously downloaded.
  • Fixed logging of forwarded sensor events.
  • Updated RAPIX Addressing Manual and added it to the installer.

RAPIX Addressing v6.11 (12 December 2018)

  • Prevented DALI line scan from moving new discovered DALI devices to the confirmed addresses.
  • Copying and pasting Scene Control (New Scene) templates on the eHub GUI will paste them as Scene Control templates.
  • Fixed the Scene Control (New Scene) template programming occasionally losing Member and scene info.
  • Improved the Database/Live filter pre-selection on the Addressing view for USB DALI lines.

RAPIX Addressing v6.10 (08 November 2018)

  • Changed in-line editing of DALI Device name on the Addressing view. Press F2 to edit non – default device name.
  • Default the DB/Live Addressing View grids to DB when there is no live network, and default them to live when network is available.
  • Open DALI device properties editor on double-click from the Groups and Scenes views.
  • Light level sensor calibration dialog now allows setting light level above 1000 Lux.
  • Renamed the ‘Save to Network’ check box on the DALI Device editor to ‘Save to Live Device’.
  • Improved display when editing multiple DALI Devices.
  • Disabled the on/off/level buttons when eHub is selected.
  • Log RAPIX software version when software starts and project file name when loaded.
  • DALI Logger: Simplified the DALI Logger filter by merging the Command filter with the Message Type filter.
  • DALI Logger: The DALI Logger Message Type filter configuration is remembered and applied when the DALI Logger window opens.
  • DALI Logger: Imported log file now uses time zone from the site.
  • Templates: Show template ID and version at top of template editor.
  • Templates: Improved the way that the timer template handles other sources controlling the Zone.
  • Templates: Improved the Motion Sensor template pop-up hint.

RAPIX Addressing v6.9 (31 August 2018)

  • Added template: Power Up Action.
  • Fixed an exception occurring sometimes when swapping addresses.
  • Improved tool-tips in the grid on the Addressing view to include device names and other info.

RAPIX Addressing v6.8 (14 August 2018)

  • Made eHub peripheral product information accessible on eHub main GUI via channel pop-up menu.
  • Added Project Save As.This can be used for creation of project backup copies.
  • Added eHub Dry Contact state visual indication to eHub GUI.
  • Added DALI line conflict resolution summary.
  • Show device type as Unknown if it does not reply to the Query Device Type command.
  • Improved sorting of DALI devices on the Groups and Scenes views.
  • Improved logging of uDID generated messages.
  • Improved the format of the date and time messages appearing in the DALI logger.
  • Improved the Motion Sensor template.
  • Improved templates filtering on the Template Selection dialogue.
  • Improved eHub programming when 5 or more slave sensors are used.
  • Don’t show the Start Function Test and Start Duration Test buttons on the DALI device GUI when editing multiple devices.
  • Improved the Dimmer Timer template.

RAPIX Addressing v6.7 (25 July 2018)

  • Added firmware update for RAPIX Xi devices (under tools menu).
  • Added a button for deep scan.
  • Added Reboot button to eHub GUI.
  • Added the Duration Test Results DALI EM device status information.
  • Added the ability to start and stop the Function and Duration emergency tests.
  • Explained what the Maintain Zone State option means in the motion sensor templates.
  • Explained dwell duration in template description.
  • Show scene name in tool-tips on eHub GUI.
  • Show eHub port details on eHub GUI Advanced tab.
  • Improved behaviour of toggle timer in Timer templates.
  • Improved behaviour of motion sensor templates.
  • Improved behaviour of Zone and Xi Timer template.
  • Default programming for eHub LCD should be to have beep ON.
  • Other minor improvements.

RAPIX Addressing v6.6 (26 April 2018)

  • eHub firmware update over DALI (under tools menu).
  • Added template “Zone and Xi Timer”.
  • Added DALI Level option for adjacent zones to the “Motion Sensor Advanced” template.
  • Fixed the DALI Logger short address filter.

RAPIX Addressing v3.3 (22 March 2016)

  • eHub Scripts Update

RAPIX Integrator

RAPIX Integrator – the professional tool for commissioning a RAPIX Lighting System.

To use RAPIX Integrator: the connection to a DALI line is made using a uDID – USB to DALI interface Device.

Alternatively, all DALI lines in an installation can be commissioned through one or more RAPIX Zone Controllers or RAPIX Ethernet DALI Interfaces.

 

Release Notes

Version 12.8.0, added: 21 March 2024

Improvements

  • Select correct default DALI-2 short address when adding DALI-2 input unit to the database.
  • Show new unit firmware version on the configuration dialogue after unit firmware update.
  • Fixed the Add Unit dialogue issue where it would appear populated with DALI-1 device types instead of DALI-2 device types.
  • Fixed the issue where adding DALI-1 push button would create a device in DB with unnecessary dry contact in it.
  • Fixed the issue with Excel import not importing templates for DALI-1 input units.
  • Fixed the issue with Excel export and import incorrectly exporting 2-channel Zone Controller as 4-channel variant.
  • Updated VC++ redistributable package to the latest version.

RAPIX Integrator v12.7 (19 March 2024)

New Features

  • Allow setting Operating Mode on selected DALI-2 units.
  • Added “Ramp Up or Down (Advanced)” template.
  • Added template “Toggle with Exit Delay and Flag”.
  • Double click light bulb icon now toggles Short Address on the Addressing view.
  • Added Edit button to the Groups and Scenes views.
  • Added Identify, Switch ON, and Switch OFF popup menu items to the Addressing view.

Improvements

  • Zone Controller Templates:
    • Allow deletion of templates using delete key.
    • Templates without button or sensor inputs cannot be named on the ZC template configuration dialogue.
    • Show template ID and version on the ZC Templates view.
    • Adding event does not work on the ZC template dialogue.
    • ZC template Flag Change Action does not show all operating property values.
    • NullReferenceException on the ZC Templates view if project only has eDIDs.
    • Template deprecation not working for ZC templates.
    • Show warning about duplicate input when user configures ZC template with multiple identical inputs.
    • Project Transfer button does not get highlighted after ZC template is added or edited.
  • Input Unit Templates
    • End of description missing on the template configuration dialogue.
    • Show when internal templates are used on the RAPIX Input configuration dialogue.
    • Error in zone selection is visible on template Config dialogue even though zone is selected.
    • The deprecation process does not work for internal events.
  • Incorrect tooltip on RAPIX Input dialogue.
  • Improve grids panel vertical scroll on the Addressing view.
  • Clean up Select Remote Zone Member dialogue.
  • Identify Zone button is enabled even though zone is not selected on unit configuration dialogue.
  • Allow selection of Zone sync rules for Go To Last Active Level and Continuous up/down commands.
  • Show error if Check For Updates fails to get products catalogue from Ozuno server.
  • RAPIX Mobile can have Confirm and Unconfirm buttons enabled at the same time.
  • Improved RAPIX Mobile web page help details.
  • RI sometimes shows unnecessary “Update firmware” warning for RAPIX input.
  • Disable Rules are not working on DALI-2 RAPIX sensors.
  • Do not show project report error about missing zone or scene if it is used in ZC template.
  • Can’t generate Project Report if there are live-only DALI-2 RAPIX units.
  • Added DALI Logging of QUERY RESET STATE, QUERY CONTENT DTR2, SET EXTENDED FADE TIME, GO TO LAST ACTIVE LEVEL, CONTINUOUS UP, and CONTINUOUS DOWN.
  • Fixed exceptions
    • Exception when changing ZC type.
    • Exception when opening floor plan.
    • Exception when updating eHub.
    • InvalidAsynchronousStateException when scanning DALI line.
    • SocketException when scanning DALI line through problematic eDID.

RAPIX Integrator v12.6 (16 February 2024)

Improvements

  • When opening a RAPIX unit in editor, check that sensor DALI-2 settings are correct and prompt user to auto-correct them.
  • Show if DALI-2 settings are wrong for use with motion sensor templates.
  • When adding a template, set DALI-2 sensor properties.
  • Fixed the issue with not being able to program Motion Sensor unit.
  • Fixed exception when closing one project and opening another.
  • Fixed the issue with not being able to select the Movement DALI-2 event filter.
  • Fixed problem with part of log filter not being visible.
  • Made the Zone editor drop-down wider on the Template editor dialogue so that long zone names would be fully visible.
  • Show DALI line name on the ZC Templates view in the Description column.
  • Updated “Dwell while adjacent areas are on” feature of the Motion Sensor (Advanced) template to work better with multi-line Zones.
  • Allow editing name of a Zone Logic template.
  • Improved layout of Zone Logic template.
  • Improved Common Area Keep-On template.
  • Improved Colour Cycle template.

RAPIX Integrator v12.4 (12 February 2024)

New Features

  • Added “All Templates” root tree node on the Zone Controller Templates view.
  • Added new templates:
    • Dial (Advanced) template
    • Bistable Dry Contact Zone and Flag template

Improvements

  • Fixed the screen draw glitch on the template editor dialogue the Summary panel.
  • Enable or disable indicator brightness controls on the RAPIX Input UI depending on whether the DALI-2 Application Controller is enabled.
  • Fixed the issue with SA and Input Unit address grids appearing with missing digits after resizing main form.
  • Increased the height of the info panel at the bottom of the DALI-2 unit configuration dialogue.
  • Fixed the issue with incorrect description and other details appearing on some Zone Controller templates.
  • Updated some templates:
    • Timer (Advanced) template
    • Dial Dimmer with Button Toggle
    • Bistable Dry Contact Toggle (Advanced) templates
    • Exhaust Fan Timer template
    • Zone Logic
    • Toggle Zone and Flag template
    • Scene Timer template

RAPIX Integrator v12.3 (8 February 2024)

New Features

  • Added support for DALI-2 Generic Instance Type.

Improvements

  • Fixed the issue causing option <Multiple Values> to appear when editing DALI-2 instance properties on a RAPIX input unit.
  • Improved tooltip text appearing on the Zone Controller tree node.
  • Allowed selecting Application Controller Enabled state on the DB-only RAPIX input unit.
  • Fixed exception sometimes occurring when opening 3rd party DALI-2 live unit.
  • Fixed the issue where RAPIX input unit sometimes appears not in sync after reopening project.
  • Minor improvements on the Zone Controller properties dialogue for the 2-channel ZC.
  • Signed 2 unsigned templates.
  • Allowed double-click in the Input Units grid on the Addressing view to open unit configuration dialogue.
  • Added a check for the Zone Controller type match (2-channel vs 4-channel).

RAPIX Integrator v12.2 (5 February 2024)

New Features

  • DALI-2 additions:
    • Added support for the DALI device type 254 (no device types implemented).
    • Show 8-digit serial number instead of 4 digits.
  • DALI-2 input unit (“control device”)support:
    • Detect during DALI line scan and resolve address conflicts.
    • Allow naming and confirming.
    • Allow Identification.
    • Allow programming of DALI-2 properties (62386-103, 62386-301, 62386-302, 62386-303 and 62386-304).
    • Allow placement on floor plans.
    • Added DALI-2 short address grid.
    • Added support in RAPIX Mobile.
    • Added to Project Report (list non-RAPIX input units by GTIN).
  • Added support for 2-channel Zone Controller.
  • Zone Controller Templates (for use with DALI-2 input units):
    • Show them in the Logic tab, and allow them to be added and edited.
    • List them in the project report.
    • Added Application Note describing their use (click on blue help button).
  • New Templates:
    • LCD Disable template.
    • Off with Exit Delay (Long Press) template.
    • 2-button colour temperature control template.
    • Templates specifically for Zone Controller.
  • Added support for MQTT (configured on Site tab).
  • Additions to RAPIX API.

Improvements

  • Use colour coding for RAPIX units.
  • Terminology change: Device -> Unit.
  • Fixed the issue with non-displayable character sometimes appearing in unit and button name field.
  • Updated USI datasheet.
  • Fixed the ArgumentNullException sometimes appearing when attempting to update eHub firmware.
  • Fixed the issue with RI showing ZC tree node as “not in sync”.
  • Fixed ZC tree node flickering while scanning DALI line.
  • Warn if user enters invalid site name.
  • Prevented Name and Value column ordering on the unit Configuration form.
  • Fixed child eDID tree nodes sorting order on the Floor Plans view.
  • Fixed problem with “Network properties are misconfigured” warning being shown incorrectly.
  • Improved templates:
    • Sunset Dimmer template.
    • Toggle Dimmer with Exit Delay template.
    • Toggle Dimmer Advanced template.
    • Zone Tracking template.

RAPIX Integrator v11.10 (9 January 2024)

  • Improvements
    – Fixed the InvalidCastException occurring when attempting to add a device on the Floor Plans view.

RAPIX Integrator v11.9 (20 November 2023)

  • Improvements
    – Fixed issue with the Dwell Level not able to be set in the Advanced Motion Sensor template.
    – Updated templates to use default dwell levels of 127 (50%) instead of 128 (50.4%).
    – Highlight faulty RAPIX devices on the Addressing view.
    – Fixed issue with Flag Timer template.
    – New Motion Sensor Vacancy Mode template.

RAPIX Integrator v11.8 (22 August 2023)

  • Improvements

    – Discover eDIDs dialog should allow selecting only one eDID.
    – eDID serial number and f/w version are not always visible.
    – Added hint for why eDID firmware can’t be updated.
    – Can’t readdress uDID even when not connected through it.
    – GO Mobile not working sometimes on Windows 11.
    – Add device count to project report.
    – Additional details in project summary.
    – Make Modbus settings Zone Controller selection combo box wider.
    – eHub touchscreen button name can appear in the channel name on touchscreen.
    – Datetime does not appear on eHub touchscreen fallback page when it is set to Default theme.
    – Can’t save eHub programming if device name has special characters.
    – Grey out checkbox of a device on Addressing view if it can’t be confirmed.
    – Show “Scanning Line” overlay on Addressing view instead of “No network information”.
    – Exception when adding floor plan then unticking Show grid.
    – Zones list sometimes appears blank.
    – DALI logger window not opening sometimes.

RAPIX Integrator v11.7 (14 August 2023)

  • Improvements- Templates
    – Added option Timer template for turning the Zone off by button press.
    – Replaced the single Timer template with a more basic version and an advanced one.
    – Fixed problem with the “Toggle Dimmer with Exit Delay” template when turning zone back on during exit delay.
    – Updated eHub LCD disable templates.
    – Added more Modbus details to project report
    – Improved UI performance on the Addressing view.
    – Fixed the issue with copy-paste not working when editing device name and allowed editing next device’s name on Tab key press.
    – Warn user when disabling Modbus.
    – Allow resetting Modbus configuration to default values.
    – Improved project report Modbus summary.
    – Fixed bugs with Project Report Op Prop and Flag tables.
    – RI can now discover eDIDs on different subnets and it can change their IP address using TCP first and if unsuccessful then UDP.
    – Show eDID as “Device Error” on the eDID Discovery dialogue if RI can connect to its 10001 port but can’t handshake with it.
    – Floor Plans
    – Allowed scaling selected on the floor plan devices.
    – Fixed the issue with zones not appearing in the list on the Floor Plans view.
    – Fixed the issue with device not appearing selected on the Floor Plans view after it is dropped on the floor plan.

RAPIX Integrator v11.6 (3 July 2023)

  • New Features
    – Allowed drawing rectangular zones on the floor plan.
    – Added summary of Modbus settings to the Project Report.
    – Added support for using RAPIX Scenes, Flags and Operating Properties via Modbus.
  • Improvements
    – Floor Plans
    – Fixed the issue causing Push Button picture not to appear on the floor plan.
    – Fixed the issue with zone drawing on the floor plan always snapping to grid.
    – Fixed the “Snap to grid” not disabling properly when selecting floor plans or opening project.
    – Prevented device from moving on the floor plans after reopening project.
    – Fixed RI crashing sometimes when adding PDF floor plan.
    – Fixed the issue with floor plan settings from previous project being visible after creating new project.
    – Fixed the exception when clicking the Grid Settings button on the Floor Plans view when there is no floor plan.
    – Fixed the exception occurring when clicking Show Grid on the floor plans view on a new project.
    – Do not select zone under mouse on the floor plan when in Pan or Zoom mode.
    – Fixed the Snap All to Grid button working only when the Snap to Grid checkbox is checked.
    – Improved how RAPIX Integrator resolves device type conflicts.
    – Improved handling of compound vs non-compound LED device type mismatch.
    – Added two scene timer templates.
    – Simplified the Modbus Settings.
    – Log meaningful error message for errors connecting to Zone Controllers.
    – Don’t log repeated error messages.
    – Added explanation of Zone sync rules.
    – Don’t show Zone Sync Rules on the Zones view if project does not have zone controllers or if zone has only one member.

RAPIX Integrator v11.5 (24 May 2023)

  • New Features
    – Added support for DALI Device Type 5 (DC Voltage Converter).
    – Show DALI Device Type when adding new device.
    – Allowed naming unencrypted connections.
    – Warn if a DALI line is controlled by broadcast but has virtual devices or switched maintained EM devices.
  • Improvements
    – Fixed the issue with the DALI Line buttons appearing disabled incorrectly.
    – Adjusted the Zone Controller properties page to prevent scroll bar from appearing by default.
    – Fixed the issue with zones list not refreshing when clicking filter buttons on the Zones view.
    – Improved mobile phone handling of processing delays.
    – Floor Plans
    Fixed issue where deleting device would not delete its graphical element from the floor plan.
    The “Add Zone” button on the Floor Plans view will now be disabled in Zoom/Pan mode.
    Fixed the issue with device snapping to grid when adding it to the floor plan when the Snap to Grid option is unticked.
    Fixed the issue with Undo accidentally removing device graphical element.
    – Excel export/import
    Don’t export empty, unnamed zones or scenes.
    Fixed export where there are duplicate names.
    Fixed export of hidden configured switches.
    Fixed export for interfaces, lines, groups, zones, scenes, and devices with blank names.
    Fixed problem with importing when there is a named DALI line with no devices.
    Fixed bug where import was reporting RAPIX sensor changing from light level to motion.
    Fixed bug where import would describe Xi Devices as “ehub”.

RAPIX Integrator v11.4 (8 May 2023)

  • New Features
    – Added support for Ozuno Blind & Shutter Relay.
    – DALI Logger:
    DALI Logger now remembers the selected item when filters are changed.
    DALI Logger has new button to scroll to selected item.
    Made RAPIX Sensor log messages more readable when there is no sensor device in DB.
    – Option to show grid on floor plans.
  • Improvements
    – Fixed the issue with Template Mode not working with some scene templates.
    – Fixed template editor issue with header section disappearing when it should be visible.
    – Warn if user tries to use an invalid Zone or Scene number in Excel import.
    – Ensured the Zone ID value that can be entered on the Zones view is within the 1 – 65534 range.
    – Prevented tree view from flickering during DALI line scan.
    – Made UI better reflect the actual state of devices during and after scan.
    – Fixed the issue with floor plan CAD elements appearing not selectable and device elements appearing dimmed.
    – Updated the Long Range LLS datasheet.
    – Mobile Phone usage improvements:
    Return to previous page after error message is displayed.
    Prevent error message from sometimes being shown incorrectly.
    Allow mobile phone user to get control back if phone’s IP Address changes.
    – Fixed some exceptions.

RAPIX Integrator v11.3 (29 March 2023)

  • Improvements
    – Added splash screen.
    – Fixed the issue causing software running on some PCs not to connect to zone controllers.
    – Fixed the issue with an alternative connection to eDID not working.

RAPIX Integrator v11.2 (21 March 2023)

  • Improvements
    – Fixed the issue with the drop-down list appearing blank on the RF Schedules view in RI.
    – Fixed the drop-down colour selection lists on eHub GUI showing text instead of colour.

RAPIX Integrator v11.1 (17 March 2023)

  • Improvements
    – Fixed bug with readdressing device using go mobile not confirming the device.
    – Fixed the issue with incorrect time editor control being used on the RF Schedules view.

RAPIX Integrator v11.0 (16 March 2023)

  • New Features
    – Updated RAPIX Integrator to be a 64-bit application.
    – Added the ability to select an alternative URL for each Zone Controller and eDID for working with remote sites.
    – Added button to refresh the connection status of Zone Controllers.
    – Added support for RAPIX Facilities:
    – RAPIX Facilities schedules.
    – E-mail details.
    – User details.
    – Floor plans:
    – Allow user to place symbols for RAPIX devices.
    – Drag and drop device symbols onto floor plans.
    – Allow floor plan to be dimmed.
    – Allow floor plan zone layer colour to be selected.
    – Options for aligning symbols.
    – Hovering over a device symbol will show details.
    – Right-click menu to allow controlling and viewing device.
    – Added help for using floor plans.
    – New device symbols, categories and colours.
    – Copy and paste of symbol style.
    – Added ability to undo changes.
    – Allowed accepting or rejecting changes user made to a project via RAPIX API.
  • Improvements
    – Clearing USI device on UI will put it in the “from factory” state and thus allow button identification.
    – Use TCP protocol instead of UDP when configuring eDID.
    – Fixed issue with the RAPIX Occ Sensor incorrectly importing from Excel.
    – Updated Zone Controller data sheet and installation guide in device catalogue.
    – Updated motion sensor templates to allow motion to turn on zone during dwell in vacancy mode.
    – Updated motion sensor templates to allow occupancy/vacancy to be set by Operating Property.
    – Fixed template form colour selection combo.
    – Sort interfaces by id when the option to display the id is selected.
    – Fixed the issue with 30M disable rules not working.
    – Updates to the Network Tree tooltips to show Zone Controller master and connection details and more details for DALI Lines.
    – Show warning if EDID has no parent Zone Controller.
    – Fixed display of colour DALI scenes for compound devices
    – Fixed an exception occurring when closing the DALI Logger window while scanning DALI line.
    – Fixed exception opening RAPIX API form.
    – Fixed Excel import of compound devices.
    – Fixed problem with mobile phone usage showing Communication Error sometimes.
    – Fixed exception when using DALI Log form for walk test.
    – Fixed exception when setting EDID IP Address.
    – Fixed bug with reading and setting EDID subnet.
    – Fixed display of colour DALI scenes for compound devices.
    – Fixed the exception sometimes occurring when deleting eDID.
    – Fixed Network tree filter.

RAPIX Integrator v10.11 (17 November 2022)

  • Allow use of email server port number greater than 100.
  • Allow selection of secondary Zone Controller for Modbus connection.

RAPIX Integrator v10.10 (26 October 2022)

  • Fixed the error that was appearing when programming Dry Contact on RAPIX Motion Sensor.

RAPIX Integrator v10.9 (24 October 2022)

  • Increased time-out on mobile phone before showing error message.
  • Fixed display of selected colour in colour control templates.

RAPIX Integrator v10.8 (14 October 2022)

  • Fixed the issue with Confirm All Devices sometimes not working and Confirm individual device sometimes showing unnecessary warning.

RAPIX Integrator v10.7 (11 October 2022)

  • New colour control templates.
  • Show Interface ID as an option on the tree view and allow collapsing and expanding interface nodes.
  • Fixed exception that could occur when opening DALI Log.
  • Fixed the issue with USI live device GUI not opening if there are programmed disable rules.
  • Show warning when adding interface device with duplicate IP Address.
  • Made DALI Line Name edit boxes wider.
  • Fixed problem with setting the eHub rotary resolution.
  • Updated Motion Sensor with Exit Delay template.
  • Highlight Project Transfer button when any of these change: users, unencrypted connections, zones, scenes, user scripts, schedules, zones used by Rapix Input devices.
  • Show an error message if function test or duration test fails to start on the device configuration dialogue.
  • When using Go Mobile, show error if phone goes out of WiFi range.
  • Prevent double click on mobile web page on iPhone from zooming.
  • Fixed resizing and closing of RAPIX API form.

RAPIX Integrator v10.6 (23 August 2022)

  • Added support for new products:
    • RAPIX Push Buttons
    • RAPIX Diva Buttons
    • RAPIX Dials
  • Added Tools menu item to allow stopping EM Function and Duration tests on site.
  • Allowed copying and pasting of DALI device properties.
  • Show pop-up hint on addressing tab showing compound device details.
  • Added toolbar buttons to Zones, Scenes and Xi Properties views to allow showing Zone ID, Sense ID, Operating Property Number and Flag Group Value.
  • Added Zone Tracking template.
  • Added Zone Logic template.
  • Improved logged DALI message when there is no Forward Frame.
  • In DALI Log, show details when setting colour or fade time.
  • Fixed problem in Mobile phone control where you could not navigate away from an unpowered DALI Line.
  • Fixed eHub motion sensor channel appearing without motion sensor inputs.
  • Warn if user has set warmest CT above coolest CT.
  • Fixed exception when showing floor plans.
  • Allow wider selection of colour temperatures from addressing tab.
  • Fixed problem with scripts continuing to run if not recompiled after deleting last script.
  • Warn user if pasting blank device configuration to another device.
  • Fixed exception when swapping eHub channels.
  • Show missing custom template ID on the error dialogue when loading programming from a RAPIX device.
  • Improved sorting by time on the schedules tab.
  • When confirming a compound device where there is a minor mismatch in type, retain as much configuration data as possible.
  • Improved options for correcting mis-matched eHub channel.
  • Prevented exception occurring in some rare cases when scanning DALI line in RAPIX Addressing.
  • Order child eDIDs by name when rendering tree of interfaces and DALI lines on the Network view.
  • Allow scrolling on mobile phone button and sensor identify pages.
  • Fixed display of compound device type.
  • eHub GUI will now offer to Configure New channel whenever there is a channel type mismatch between DB and live.
  • Rotary and sensor inputs on eHub GUI will appear as circles while push button inputs will appear as rectangles with rounded corners.
  • Fixed child eDIDs sometimes appearing in swapped order in the interfaces treelist on the Network view.

RAPIX Integrator v10.5 (29 June 2022)

  • Allow user to select DALI Line.
  • Identification of RAPIX buttons.
  • Identification of RAPIX sensors.

New options for allocating short addresses

  • Don’t use Short Address 0.
  • Allocate SA starting from low SA, or starting from high SA.

Improvements

  • Allow RAPIX Integrator to discover and configure eDIDs that are on different subnets.
  • Improved reporting of compound device types.
  • Fixed problem with reporting results of Short Address allocation.
  • Allow a user to select less than 4 schedule groups in auto-build for RAPIX Facilities.
  • Allowed editing offline eDID.
  • Fixed problem with sync check of compound devices.
  • Allowed selecting Dynamic Fast Fade Time for LED DALI devices.

RAPIX Integrator v10.4 (23 May 2022)

  • New features for mobile phone use:
  • Allow user to select DALI Line.
  • Identification of RAPIX buttons.
  • Identification of RAPIX sensors.
  • New options for allocating short addresses
  • Don’t use Short Address 0.
  • Allocate SA starting from low SA, or starting from high SA.
  • Improvements
  • Improved reporting of compound device types.
  • Fixed problem with reporting results of Short Address allocation.
  • Fixed problem with sync check of compound devices.
  • Allowed selecting Dynamic Fast Fade Time for LED DALI devices.

RAPIX Integrator v10.3 (26 April 2022)

  • Fixed the issue with not being able to select remote zone on eHub on a child eDID DALI line.

RAPIX Integrator v10.2 (17 March 2022)

  • Added support for the new software RAPIX Facilities.
  • Added RAPIX API dialogue.
  • Fixed USB DID Driver installer sometimes not installing the driver on new Win10 and Win11 laptops.
  • Added scroll to Zone Controller Properties tab.
  • Improved info links that navigate to Ozuno web site.

RAPIX Integrator v10.1 (1 February 2022)

  • Added new template Scene Sequence (bistable dry contact).
  • Updated USB DID Driver.

RAPIX Integrator v10.0 (12 January 2022)

  • Added support for using an EDID as an additional Zone Controller DALI interface. (Application Note PDF)
  • Allow Zone Controller date and time to be set from RAPIX Integrator.
  • Added new “Dial with Selectable Granularity” template.
  • Auto-fill IP settings when adding a DALI Interface.
  • Improved the Xi Flag Change Event template.
  • Improved the Xi Operating Property Change Event template.
  • Hide “dial” templates for dry contact inputs.
  • In template editor, added text next to expand/contract chevron to show its purpose.
  • Fixed problem with colour select form not allowing colour selection for some devices.
  • Fixed problem with Zone Controller properties tab sometimes incorrectly showing “Network properties are misconfigured”.
  • Various minor improvements to the Project Report.
  • Fixed the logic “catch-up” process.
  • Added confirmation for excluding logic modules to make it harder to do by accident.

RAPIX Integrator v9.8 (22 November 2021)

  • Allow Zone Controller date/time to be set from RAPIX Integrator (useful for testing schedules and logic).
  • Added a DALI Query log filter option to enable the background query messages to be hidden.
  • Fixed problem with setting DALI scene colour.
  • Fixed the “Discover” button for adding new Zone Controllers.
  • The DALI log window will be removed from the task bar when closed.
  • Updated the Technical Support tab on the About box.

RAPIX Integrator v9.7 (25 October 2021)

  • Show eHub schedules on schedules tab.
  • Added list of project-related contacts.
  • Added site address property.
  • Added location information for every DALI device.
  • Updates for log form:
    • Added option for viewing Button Pressed events to the Log Form.
    • Added Walk Test mode to Log Form.
  • DALI-2 support:
    • handle 8 byte serial numbers
    • show PING command in log
  • Added support for new Zone Controller mesh.
  • Improved handling of DALI Devices that don’t reply to valid READ MEMORY LOCATION commands.
  • Don’t allow selection of USB Zones in Schedules or Logic.
  • Fixed problem with listing sensors in project summary.
  • In project report, show complete list of Zones and Scenes sorted by name and by id.
  • Fixed problem with bottom of log filter view hidden.
  • Fixed problem with creating Zone Controller summary from compact log file.

RAPIX Integrator v9.5 (3 September 2021)

  • Allow setting the group membership of multiple devices on the Group tab using SHIFT + Click.
  • New Templates
    • Toggle Dimmer and Xi Flag
    • Toggle Dimmer with Exit Delay
    • Motion Sensor with Two Delays
  • Help button for getting Zone Controller logs
  • In Short Address list, highlight missing devices.
  • Closing the DALI log now leaves it paused in the background so that the logged data is not lost.
  • Allow better resizing of logic editor.
  • In template drop-down lists, show items in sorted order.
  • Improved the wording of some error messages.
  • Improved the description of some template descriptions.
  • Support changes to Zone Controller scan process.
  • When resolving address conflicts, attempt to move devices back to their correct address.
  • Fixed problem with importing DALI Log from Zone Controller with no project.

RAPIX Integrator v9.4 (17 June 2021)

  • Zone Controller Report (lists details of all connected Zone Controllers).
  • Added ability to set Zone Controller log level from RAPIX Integrator.
  • Added Help menu.
  • New templates:
    • Light Level Report.
    • Light Level Operating Property.
    • Do Nothing.
  • Support for new Zone Controller DALI Log:
    • In Log Form, added import of DALI Log (conversion to RI log format).
    • In Log Form, added button to generate summary data file for graphing of parameters over time.
  • Fixed Motion Sensor Slave template not working on Dry Contact inputs of Xi Sensor and Universal Input devices.
  • When hovering mouse over DALI Line shown in red, show hint describing problem.
  • Fixed problem with slave sensor template.
  • Updates to logic manual.
  • When using mobile phone to move, confirm or unconfirm devices, show device confirmed status (i.e. black).
  • Prevent exception when re-addressing devices.
  • Prevent exception when converting from Colour Temperature to RGB.
  • If there are 6 DALI Interfaces or less, show the project tree expanded.
  • In the Select Remote Zones form, allow local Zones to be selected also.
  • Show error message when transferring currently open project from Zone Controller.
  • Added pop-up hint for everywhere that the perceived brightness “eye” icon is used.
  • Improved error message when saving to eHub fails.
  • While updating eHub or Xi Device firmware, prevent the rest of the program from being used.
  • Changed the default scene fade time to 1 second.
  • Improvements to eHub and Xi Disable Rule forms:
    • Allow long names to be seen in drop-down lists.
    • Sort items in drop-down list.
    • Increased width of columns.
    • Show a hint for long descriptions.
    • Clarified error message when trying to use an unused scene in a disable rule.

RAPIX Integrator v9.2 (19 April 2021)

  • Logic
    • Added support for serial ports.
    • Added level conversion methods.
    • Added IsFirstRun property.
    • Allow an excluded module to be edited.
    • Fixed problem with logic messages sometimes not shown in RAPIX Integrator log.
    • Changed name of top-level logic tree node from “Standard” to “Modules” to reduce confusion. Updated help file to match.
  • New scene sequence template.
  • Added ability for log to show Zone Controller Master/Slave arbitration system events.

RAPIX Integrator v9.1 (1 March 2021)

  • The “Disable Out-of-box Behaviour” feature for Xi Sensors and Universal Inputs.
  • Logic
  • Clearing all addresses now includes Xi Devices.

RAPIX Integrator v9.0 (2 February 2021)

  • Speed-optimised Project Transfer to Zone Controllers.
  • Improvements to Project Report:Fixed DALI Scene usage.
  • Made DALI Scene tables more compact.
  • Warn if DALI Groups and DALI Scenes are defined but not used.
  • Warn if firmware version is not the same across ZCs in the project.
  • Fixed issue with Project Report where a Zone is used in more than one scene.
  • Added list of the Xi Operating Properties and Xi Flags to the Project Export (for use with third-party systems).
  • Fixed exceptions.

RAPIX Integrator v8.12 (29 October 2020)

  • Allowed updating OS on multiple zone controllers in parallel.
  • Clarified confirmation messages for zone controller f/w update, OS update, Reboot and Clear actions.
  • Added support for the Long Range Xi Sensor.
  • Disabled indicator for Scene Cycle/Sequence templates.
  • Split room join template into three for clarity. Removed unused timer from toggle dimmer template.
  • Fixed bug with setting colour scenes.
  • Updated the format of the export project data file.

RAPIX Integrator v8.11 (29 October 2020)

  • Project Report
    • Test for overlapping Zones in Project Report.
  • Templates
    • Added more blind control templates.
  • RAPIX Mobile
    • Allow addressing Xi Devices.
    • Allow setting DALI groups.
    • Allow DALI line scan.
    • Show basic info about the DALI Line.
  • Fixed ConstraintException Value ‘-1’ occurring sometimes when adding new Xi Scene.

RAPIX Integrator v8.10 (9 September 2020)

  • Project Report
    • In the project summary, highlight items that are a potential problem.
    • Show Zone tracking rules in project summary.
    • Fixed error with project report not showing Xi Input Dry Contact info.
    • Added details of redundant Zone sync rules to Project Report.
  • Templates
    • Fixed Scene Cycle template.
    • Improved handling of templates for dials.
    • Added Scene Cycle 2 button template for colour control.
    • Updated Scene Cycle template to work with button click as an option.
    • Added new option to Scene Timer template.
  • On Scene Blast form, added all/none buttons for mask.
  • Fixed sorting of schedule events by time.
  • Added Catch-Up options for Zone Controller schedules.

RAPIX Integrator v8.9 (17 August 2020)

  • Allow selection of Zone Controller status scan period.
  • In project report, show break-down of device types.
  • In project report, warn if a Zone has lots of short addresses.
  • Improved reliability of the eHub firmware update over Ethernet.
  • Don’t show warning about no NTP on the eHub 3.0 GUI if there is no live device.

RAPIX Integrator v8.8 (4 August 2020)

  • Template light level control – allow larger hysteresis and show actual range.
  • Fixed problem with TimeZone selection for non-English versions of Windows.
  • Increased the height of the header of some templates.

RAPIX Integrator v8.7 (1 July 2020)

  • Fixed DALI group membership change on the Groups view affecting device identification.
  • Fixed the ObjectDisposedException exception that could occur when saving USI programming while shortening and opening its dry contacts.
  • Improved reliability of sorting of schedules in the Schedules tree-view after adding, removing or editing a schedule.
  • Fixed exception that could occur on eHub GUI when updating Ethernet info on the Info view.
  • Changed the way that eHub scenes are stored to fix issue with scene indicators.
  • Fixed the issue with Scene view showing incorrect parent eHub.
  • Added Blind-control templates.
  • Added sunset switch for scenes template.
  • Added mode selection to Motion Sensor with Exit Delay template.
  • Log DALI Type 4 Application Extended Commands.
  • In project report, show DALI version.
  • Added support for DALI-2 devices.

RAPIX Integrator v8.6 (1 July 2020)

  • Fixed the eHub 3.0 Schedules disabling feature.
  • Improved when warning message about no NTP service appears on the eHub 3.0 Schedules view.

RAPIX Integrator v8.5 (25 June 2020)

  • Fixed Go Mobile help page scrolling and phone simulator.
  • Improved support for RGBWAF DALI Type 8 devices.
  • Improved logging of exceptions related to opening Device Catalogue.
  • Fixed the eHub programming not loading from live device if it was programmed with a Scene Cycle template.
  • Fixed the exception sometimes occurring when clicking Clear button on the Xi Sensor GUI.

RAPIX Integrator v8.4 (17 June 2020)

  • IP address on the eHub 3.0 Info tab is now a clickable URL.
  • Don’t show Schedule info on the Xi Sensor and Universal Input GUIs.
  • Improved Xi Change templates.
  • Stopped showing warning about no NTP on the eHub 3.0 GUI Schedules tab when device is configured to Accept NTP Broadcasts.
  • Schedule name edit box will now appear on the Schedules view.

RAPIX Integrator v8.3 (9 June 2020)

  • Added support for eHub Schedules.
  • Added information on eHub editor to show details of Ethernet and NTP (for eHub firmware 3.0 or later).
  • Added buttons to unconfirm all devices and clear short address of all devices.
  • Added error messages when adding scenes and schedules to project with no Zone Controllers.
  • Show when scenes are stored in Xi Device.
  • Raise an error when attempting to edit Xi device entry when its DB and live types do not match.
  • Added clear project button to Zone Controller view.
  • Added help buttons to various locations to show related App Note.
  • Prevented internal event templates from appearing in the list of available templates when programming Xi Sensor.
  • Prevented PC from going to sleep when updating eHub or Xi Device firmware.
  • Stopped showing the error message about device type conflict when moving device to a different address.
  • Improved performance of loading live eHub programming on large projects.
  • Replaced Common Area Control template with two new ones.
  • Fixed header height on templates. Fixed maximum pulse level in templates.
  • In scene templates, added hyperlink to colour control App Note.
  • Allowed adding eHub v3.0 and eHub v2.3 to database.
  • Fixed the eHub firmware import throwing exception when importing from a network drive starting with double slash.
  • Fixed an exception occurring sometimes when importing Zone Controller firmware file from email attachment.
  • Fixed an exception occurring sometimes when confirming short addresses or using RAPIX Mobile.
  • Removed the Add button from the eHub GUI Templates page.
  • Clarified some of the eHub error messages.
  • Improved Xi Flag Group presentation in the Project Report.

RAPIX Integrator v8.2 (23 January 2020)

  • Improved firmware update of Rapix Emergency DALI devices.
  • Fixed the “Could not open project” error appearing when attempting to open a project.
  • Made the header of the “Set Static IP Address” dialog taller so that all text on it could be clearly visible.
  • Improved description of scene templates.
  • In the Scene Member list, show correct info for colour when there is a DALI Scene selected. Same for project report.
  • Button to show help for Modbus on the Site view.
  • Improved behaviour with templates containing multiple DALI Scenes such as Scene Cycle.
  • Improved Motion Sensor templates.
  • Added Scene Cycle DALI template.
  • Added link to help/support information to some templates.
  • Show Scene conflict decoration on the Scenes view when there is a scene colour.
  • Allowed selecting colour on the Scene Blast dialogue.
  • Added Scene Auto-create to the Scene Blast dialogue.
  • Fixed the issue with getting device status from the offline devices.
  • Added Modbus config errors to Project Report.
  • Improved Project Report.
  • Programming of Rapix input devices can now be force-saved, i.e. DB programming can be saved to live device even if nothing was changed on the device configuration dialogue.
  • Don’t allow using empty zones in Rapix input devices.
  • Improved Zone and Scene member pop-up tooltip.
  • Added Common Area Control template.
  • Added main menu item Tools\View Logs.

RAPIX Integrator v8.1 (23 January 2020)

  • Modbus error reporting.
  • Show the correct number of inputs for the Universal Input device in database.
  • Allowed RAPIX Integrator download and automatically install RAPIX Input firmware images.
  • Updated Rapix TeamViewer Client to the latest version.

RAPIX Integrator v8.0 (31 December 2019)

  • Excel import/export of eHub Disable Rules.
  • Fixed the DALI logger issue where it would stop logging all traffic on a DALI line after receiving an unknown/malformed forward frame.
  • Changed Xi Scene label on the Configure Schedule Event dialogue.
  • New installer:
    • Install software in \Program Files (x86)\Ozuno instead of \Program Files (x86)\Diginet
    • Store project files in \Documents\Ozuno instead of \Documents\Diginet
    • Store templates and firmware in \ProgramData\Ozuno instead of \ProgramData\Diginet
    • Changed registry settings from HKEY_CURRENT_USER\Software\Diginet to HKEY_CURRENT_USER\Software\Ozuno
  • Added templates:
    • Dim Only
    • Set Scene and Flag
    • Toggle (Long Press)
    • Bell Press (Long Press)
    • Dial/Button Dimmer
  • Improved template filtering to hide infrequently used templates.
  • Added Modbus support.
  • Fixed device identification not working on the Xi device f/w update dialogue.
  • Fixed Dry Contact state sometimes appearing as Closed on UI even when that DC is actually open.
  • Added support for XY colour.
  • Fixed the Colour Value not saving to the Scene Colour table in the project database.
  • Fixed problem with colour devices not having auto activation enabled.
  • Fixed sunrise/sunset calculations for GMT +12 (e.g. Wellington, New Zealand).
  • Added support for the Rapix Xi Universal Switch Input.

RAPIX Integrator v7.3 (16 October 2019)

  • Show which Zone Controller is the Master.
  • Supported long fade times (from 2 minutes to 24 hours).
  • Improved support for colour
    • Allowed setting colour for the selected devices, groups and broadcast. Also allowed the Set Colour dialogue height change dynamically when selecting colour type.
    • Allowed setting zone colour from the Zones view.
    • Allowed setting colour in Xi Scene.
    • Allowed setting colour in Schedule Event.
    • Added colour details to project report.
    • Added colour details to Excel import/export.
  • Dynamic tooltip and icon on the Addressing view for non-compliant devices, errors, sync and other issues.
  • Reworked identification of the eHub channels and added identification of eHub individual inputs.
  • Groups and scenes will now be automatically preselected in the identification drop-down list when selecting them on the Groups and Scenes views.
  • Added dial/dimmer template.
  • Disabled Xi device editing when device’s DB and network types are different.
  • Allowed resizing the Device Name column on the Addressing view. The column size will be set to default when software starts.
  • Improved the subnet mask validation when adding Zone Controller or editing its network settings.
  • Improved performance of confirmation of an Xi Device when there is DB and live device type mismatch.
  • Fixed bug with saving MASK colour to live devices from DALI device editor.
  • In DALI Device editor, if GTIN or serial is invalid, show as “N/A”.
  • Fixed a problem with resetting DALI Type 8 devices.
  • Changed the Motion and Light Level Sensor template name to Motion in Darkness.
  • Fixed Motion Sensor With Exit Delay template.
  • Fixed the issue with Global DALI Device Programming not saving scene changes to live devices.
  • It will no longer be possible to accidentally delete confirmed devices when deleting multiple selected devices.
  • Allowed unconfirming Xi address if it happened to be occupied by a DALI interface device after address conflict resolution.
  • Improved the appearance of title on the Network, Zones and Xi Scenes views when resizing panels with a splitter.
  • Prevented the Network Interfaces tree from expanding when main window maximises.
  • Confirming Xi device will now change the database device type if it is not the same as on live device.
  • Fixed the Xi Sensor motion indicator green ring not appearing on GUI when motion is detected.
  • Fixed the Duration editor not working properly for the Sunset Switch template when attempting to set values below 30 minutes.
  • eHub GUI will no longer show a dry contact open or closed state if there is no live device.
  • Improved performance of the DALI Device Global Programming on large projects.
  • Project Report now includes eHub internal events.
  • Fixed an exception occasionally occurring when changing device’s address.
  • Updated Zone Controller link icons and improved their usage.
  • Fixed a few issues with Excel import.
  • Fixed the Disable Rules dialog not appearing for an Xi Sensor dry contact.
  • Updated the Tech Support tab on the About box.
  • Use tooltip on the Schedule event dialogue when showing colour values that have long description.

RAPIX Integrator v7.2 (29 August 2019)

  • Allowed user to save just the changes for the eHub and DALI Xi Occupancy Sensor to reduce save time.
  • Added editor for eHub internal event templates and removed the need for them to be associated with an unused input.
  • Fixed the issue where DALI logger stops working after unrecognised or malformed command.
  • Fixed the issue with the Light Level Maintenance template not retaining the selected Light Level value.
  • Fixed the NullReferenceException occasionally occurring when closing RI after using DALI logger.
  • Allowed resizing the Network view. Splitter distance will be saved when closing software.
  • Fixed the mouse wheel scroll down event not working on the Light Level track bar.
  • Fixed an issue with the Excel import not using Zone Names in templates. Added additional checks of Zone Controller worksheet data.

RAPIX Integrator v7.1 (15 August 2019)

  • Added Watchdog Timer template.
  • Added Motion Sensor and Exit Delay template.
  • Excel import/export improvements
    • Added Xi Flags and Operating Properties.
    • Added Schedules.
    • Added Xi Scenes.
    • USB DALI lines.
    • Fixed the issue where if user puts the “Xi Devices” list twice in a work-sheet, the import gets stuck in an infinite loop.
    • Allowed use of Zone and Xi Scene names in import of templates.
  • Added Ozuno web site link to the About box.
  • Added Xi Devices Global Programming.
  • Excel import/export improvements
  • Improved handling of Xi Device and Zone Controller extended address conflict.
  • Improved Dry Contact usage by allowing dimmer and advanced templates.
  • Improved Toggle Advanced template.
  • Reduced log time stamp decimal places.
  • Clarified on the UI how schedules use Xi Flags and Operating Properties.
  • Fixed the NullRefernceException occurring when starting RAPIX Addressing on Windows 7 that has Firewall blocking Mobile web server port.
  • Fixed an exception occurring on software start up if user didn’t have write permissions to the Debug.log file.
  • Fixed the Project summary not listing Flags used in DALI Xi Occupancy Sensor and Universal Input Dry Contacts.
  • Improved Add Device dialogue
  • Fixed the Change Template not changing template on a dry contact.
  • Added floor plan snap to grid option.
  • Save selected floor plan Background Theme to the project database.
  • Improved filtering of allowed templates on a RAPIX DALI Xi Occupancy Sensor dry contact.
  • Tidied templates that use internal events.
  • Improved software performance on large projects when moving, copying or changing eHub input programming.

RAPIX Integrator v7.0 (10 July 2019)

  • Added support for the DALI Xi Occupancy Sensor.
  • Added project export to Excel and import from Excel.
  • Display the current light level sensor reading on the eHub GUI.
  • Added the Motion and Light Level Sensor template.
  • Added the Xi Operating Property Action template.
  • Fixed all exceptions reported by users.
  • Prevented Project Key from having characters that are easily confused on the Zone Controller LCD.
  • Fixed the Set and Clear of the Xi Flag not working on USB DALI lines.
  • Fixed the Confirm All button remaining disabled after unconfirming a device.
  • Software auto-update changed to use a new server.
  • Clarified what type of eHub input can be used with each template.
  • Improved local interface detection by the Fast Scan.
  • Project Report: Sort Zone members.
  • Project Report: Do not raise the warning about a zone not being used if it is a sub-zone.

RAPIX Integrator v6.14 (15 March 2019)

  • Fixed issues with editing multi-selected colour devices.

RAPIX Facilities

Complete Lighting Control Facilities Maintenance Software.
One software for all your facility lighting requirements.

Release Notes

Version 3.0.0, added: 1 March 2024
  • New Features
    – DALI-2 support.
    – Added support for the new DALI-2 range of RAPIX input units.
    – Added support for the 2-channel zone controller.
    – Report errors if there are unexpected devices on DALI Line.
    – Allowed setting DALI unit minimum and maximum levels using the Floor Plan right-click menu.
    – Added search box to the Unit History form.
    – Allowed viewing S/N and GTIN on the Unit History form.
    – Show details of missed duration test on the Unit History form.
  • Improvements
    – Delay RF unit check or test by up to 5 mins while zone controller is building model.
    – Improved RF unit check for Overdue Test condition.
    – Fixed the issue where RF was incorrectly reporting new EM unit as “Overdue Test”.
    – Service test result will now be set to Overdue Test only after RF detects EM unit missing 3 times in a row.

RAPIX Facilities v2.6 (22 November 2023)

  • Improvements
    – Fixed issue with RF not opening project that contains compound DALI devices.
    – Disable Floor Plans button if project does not have floor plans.

RAPIX Facilities v2.5 (20 October 2023)

  • New Features
    – Added popup menu to the Floor Plan to allow turning on, off, etc. devices and zones.
    – Installer now has a setting for RF to prevent PC from going to sleep.
    – Installer now has a page to inform user to enable auto-logon.
    – Added support for the DC Voltage DALI device type (0-10V, 1-10V).
    – Schedule Next Run Date and Time can now be edited and changes saved to RI project.
    – Fixed the issue with email server port above 100 not appearing in the Port Number edit box.
    – Wait for Model Build to finish before doing Device Presence Check.
    – Improved description of license on registration form.
    – Improved how installer checks for whether RAPIX Facilities is running.
  • Improvements- Fixed issue with PC locked licenses on PCs with multiple MAC addresses.
    – Will now automatically reconnect to disconnected DALI lines.
    – Fixed the issue with the default floor plan view sometimes not being applied.
    – Fixed the issue with the floor plans drop-down list appearing blank when there are no devices on any floor plans.

RAPIX Facilities v2.4 (24 May 2023)

  • Improvements
    – Fixed the issue with email server port above 100 not appearing in the Port Number edit box.
    – Wait for Model Build to finish before doing Device Presence Check.
    – Improved description of license on registration form.
    – Improved how installer checks for whether RAPIX Facilities is running.

RAPIX Facilities v2.3 (8 May 2023)

  • Improvements
    – Updated function test procedure to better handle devices that finish function test within 1 second.
    – For Type Mismatch error show types in a tooltip.
    – Fixed the Invalid Operation Exception that could occur when sorting devices on Device Status tab.
    – Improved check of replaced devices.
    – Bug fix: Unnecessary warning “Potential Schedule Conflict” appears in Config mode.
    – Bug fix: Transparency layer does not allow selecting CAD elements of a drawing.

RAPIX Facilities v2.2 (29 March 2023)

– Added splash screen.
– Added the “Start Duration Test Now” button.
– Correction to issue causing software running on some PCs not to connect to zone controllers.

RAPIX Facilities v2.0 (16 March 2023)

  • Initial public release

RAPIX Emergency

RAPIX Emergency is the intelligent DALI Emergency Lighting Monitoring System with ‘One Click’ commissioning.

RAPIX Emergency comes in 2 editions:

  • World Edition – 3 hours running time, 12 monthly maximum check interval.
  • Australian Edition – To suit the Australian country requirements: 90/120 minutes running time, 6 monthly maximum check interval.

A common download is used for both editions, the country requirements are selected during installation. Both editions are FREE software.

Release Notes

Version 6.0.0, added: 30 March 2022
  • Allowed importing RAPIX Integrator projects that contain EDIDs.
RAPIX Emergency (DALI) v5.10 (7 February 2022)
  • Improved support for DALI “Multiple” device type.
RAPIX Emergency (DALI) v5.9 (10 March 2021)
  • Made RAPIX Emergency connect faster to Ethernet DALI interfaces.
RAPIX Emergency (DALI) v5.8 (23 March 2020)
  • Combined World Edition and Australian Edition of RAPIX Emergency software into single installer.
  • Updated the installer software.
RAPIX Emergency (DALI) v5.7 (08 November 2018)
  • The UI performance on large projects has been significantly improved.
  • DALI lines in the test reports will be sorted by interface name and then DALI line name.
  • 0 minutes test duration instead of blank space will appear on devices that reported 0 minutes duration.
  • The test report header section has been expanded to show error percentages grouped by error types.
  • Fixed the Out Of Memory exceptions occurring when attempting to reconnect to 80+ Zone Controllers.
RAPIX Emergency (DALI) v5.5 (25 July 2018)
  • Simplified software installation and licensing.
RAPIX Emergency (DALI) v5.4 (09 January 2018)
  • Test reports in CSV format can now be generated and attached to emails in addition to the standard PDF reports.
  • Previous Test Results can now be visible in the Configuration view.
  • RAPIX Emergency will now wait for up to 8 hours (instead of 5 hours) when collecting test results after a discharge test before giving up on a device and marking it with “pending test failure”.
  • RAPIX Emergency auto-start on Windows startup can now be configured by a Supervisor user.
  • The device status pie-chart can now be hidden by a Supervisor user.
  • Manual Function Test on All Lines and manual Discharge Test can now be started from the Dashboard.

RAPIX Desktop / Touch

The RAPIX Desktop App allows lighting control from a desktop PC

The RAPIX Desktop App runs on a Windows PC, and allows control of lighting from a system tray icon.

  • Easy configuration utility.
  • Multiple control widgets can be selected and configured.
  • Keeps out of the way until needed.
  • Suitable for corporate deployments, can be deployed using Group Policy.

Release Notes

Version 4.3.0, added: 8 November 2023

      RAPIX Desktop App

  • Improvements
    – Fix some issues with web widgets.

      RAPIX Desktop Configuration Utility

  • New features
    – Remember last-used Preview Scale setting.
  • Improvements
    – Fixed the NullReferenceException occurring when starting application on Japanese Windows 10.
      RAPIX Touch (Version 4.5.0, added: 27 February 2024)
  • Improvements
    – Made it more difficult to install RT on a normal laptop

     

RAPIX Touch v4.3 (8 November 2023)

  • Improvements
    – Fix some issues with web widgets.

RAPIX Desktop App v4.1 (23 October 2023)

RAPIX Desktop Config v4.1 (23 October 2023)

RAPIX Touch v4.1 (23 October 2023)

RAPIX Desktop App

  • New Features
    • New Widgets
      – Zone Timer.
      – Blank (used as spacer).
      – Sub-heading.
      – Blind / curtain / shutter.
    • New widget features
      – Changed Scene widget to do scene toggle.
      – Added option for Zone and Scene widgets to have options for showing status.
      – Added option for Zone Timer Widget timer status.
    • New theme options:
      – Widget borders.
      – Larger widgets (for use with very high resolution screens).
      – Allow user to select all theme options.
      – More options for header.
    • Fixed problem with Widget state initialisation.
    • Show message when RD imports a file.
    • Allow user to select configuration for All Users or Current User.
  • Improvements
    – Show error message if importing a file and software is already running.
    – Improvements to logging.
    – Fixed bug with importing config for All Users (HKLM).
    – Fixed bug where it would crash if the c:\ProgramData\Ozuno\RAPIXDesktop folder did not exist.
    – Updated Flag Widget and Op Prop Widget to use theme colours.
    – Prevent settings form from being opened (and causing an exception) if there is a configuration error.
    – Fixed bug with setting theme when installed for All Users (HKLM) only.

      RAPIX Desktop Configuration Utility

  • New Features
    • New Widgets
      – Zone Timer.
      – Blank (used as spacer).
      – Sub-heading.
      – Blind / curtain / shutter.
    • Added support for RAPIX Touch:
      • New widgets only for RAPIX Touch:
        – Web page
        – Date and Time
        – Image
        – Page Selection
      • Grid of widgets.
      • Multiple pages.
      • Access control.
      • Footer options.
      • Timeout page.
    • New widget features
      – Changed Scene widget to do scene toggle.
      – Added option for Zone and Scene widgets to have options for showing status.
      – Added option for Zone Timer Widget timer status.
    • New theme options:
      – Widget borders.
      – Larger widgets (for use with very high resolution screens).
      – Allow user to select all theme options.
      – More options for header.
    • Highlight when a Widget is being edited.
    • Handle missing zone/scene etc when editing.
    • Added file save as.
    • Allow widget control to be disabled while editing to prevent accidental control of lighting.
  • Improvements
    – Fixed problem with Widget state initialisation.
    – Improvements to logging.
    – Improvements to drag and drop of widgets.
    – Fixed bug where it would crash if the c:\ProgramData\Ozuno\RAPIXDesktop folder did not exist.

      RAPIX Touch

  • First release.

RAPIX Desktop Config v3.0 (17 March 2023)

  • Rapix Desktop App and Rapix Desktop Configuration Utility
    • Updated RAPIX Desktop to be a 64-bit application.
    • Allowed editing Zone Controller scenes and schedules.

RAPIX Desktop App v2.0 (11 October 2022)

RAPIX Desktop Config v2.0 (11 October 2022)

  • Rapix Desktop App and Rapix Desktop Configuration Utility
    • Allow user to edit schedules.
    • Allow user to edit scenes.
    • Made the icon always visible.
    • Allow cancellation of widget edit
    • Updated help file
    • Added button to allow password to be viewed. Improved form re-draw.
    • Import existing configuration file
    • Allow user to edit widgets. Added scroll to widget preview.
    • Allow user to delete and rearrange controls.
    • Improved theme appearance.

RAPIX Desktop App v1.4 (8 June 2021)

RAPIX Desktop Config v1.4 (8 June 2021)

  • Rapix Desktop App
    • Added an option for the Zone level widget slider to show Target Level or Actual Level.
  • Rapix Desktop Configuration Utility
    • Added an option for the Zone level widget slider to show Target Level or Actual Level.

RAPIX Desktop App v1.3 (19 April 2021)

RAPIX Desktop Config v1.3 (19 April 2021)

  • Rapix Desktop App
    • Fixed problem with RGBW slider values “bouncing back” after a change with some DALI drivers.
    • Added logging.
  • Rapix Desktop Configuration Utility
    • Fixed problem with RGBW slider values “bouncing back” after a change with some DALI drivers.

RAPIX Desktop App v1.2 (1 April 2021)

RAPIX Desktop Config v1.2 (1 April 2021)

  • Rapix Desktop App
    • Fixed problem with colour temperature slider with high values.
    • Fixed problems with slider values “bouncing back” after a change.
  • Rapix Desktop Configuration Utility
    • Fixed problem with colour temperature slider with high values.
    • Fixed problems with slider values “bouncing back” after a change.
    • Show real-time data in preview panel.

RAPIX Desktop App v1.1 (25 March 2021)

RAPIX Desktop Config v1.1 (25 March 2021)

  • Initial public release
Scroll to Top

Register for news and notification of updates

Why Register?  Registering makes it easier to inform our customers and users about new updates and features.

We won’t fill your inbox with spam emails and we will never sell any mailing lists.